Spray booth consideration :
Spray booth only allowed using no risk of explosion and open flame ,smoking is strictly prohibited within 10 meters of the baking room or barn outsideSpray booth inside shall not store flammable and explosive materialsEach time the job is completed ; clean-up must be carried out to the spray booth ,all the material for painting must be taken out .The supply voltage shall not be lower than or higher than 10% of the specified voltage .Without the approval of the manufacturer unauthorized changes all liability caused by the equipment manufacturer no responsibilityAll liability caused by the removal and tampering protection of the safety devices without authorization, the manufacturer takes no responsibilityThe device working ,someone must monitor ,all parking position switch must be reset after work .Housing Mainland grille hosts the work-piece ;tread plate carries only the weight of the operator ,not carrying the weight of the work-piece .The ground network and its room ground recommended weekly with a vacuum cleaner to clean once Spray booth with mosquitoes ,should repellent drugs remove mosquito to paint operation.The device must be operated by professionals familiar with the operation of equipment specification .Equipment before use should open the system used in the no-load Preheat run for 20 minutes, in order to avoid adverse effects on the work-piece .
Booth Body:EPS or Rock wool panel
Wall panel :sandwich style,thickness 50mm,polystyrene or cock wool available as required .
Panels are tongue and groove connected .Roof panel is galvanized metal sheets,hot-isolated panel as optional .
Door:new style is without aluminum side,reinforcement inside,while old style is with aluminum side.
Personnel door with pressure lock automatically opens when inside pressure exceeds.
There is auto-return device on top of personnel door of some models .
Basement is made of steel ,galvanized ,easy assembled .
2rows of grids and 3rows of vein boards, or full grids,good bearing ,antisepsis and reliable .
Ramp :2pcs or full vein boards.
Intake and exhaust Cabin
Centrifugal fan,big vane and motor separated ,avoiding accidents resulting from short circuit .Centrifugal fan produces great air flow ,is easy to clean dust on vane,and is up to CE standard. In take fan is a must for all models ,while exhaust fan is collocated for some models.
European flange style ducts.Exhaust ducts are must for all models while intake ducts are collocated for some models.Manual or electrical damper to adjust air flow .
Spraying-baking transform damper ,air controlled .
Intake and exhaust ducts are separated ,avoiding interaction
Cleaning system
Twice filtration:the first one is at inlet,filtering dust above 15um,the second one is at the bottom of roof air chamber .multi-layers, good seal ,filtering dust above 5um ,up to 98% filtration rate. Four sides of filters are hided in the support trough ,assuring good seal .
Heating : Diesel burner ,fired after flame,reliable and completely burnt.
Heating exchanger ,made of stainless steel, large exchange area ,and high efficiency.
Oil tank ,oil display tube,and oil filter collocated .
Lighting :Top lights:45° assembled,tubes are different according to different models.
Sides lights:differ according to different models,700-1000Lux lighting.
Control board : Control box :high quality components ,overload ,overheat ,phase-lacking protection.Heat sensor at
inlet works when heat exceeds .The whole operation can be done after spraying/baking is preset once.
SCM as optional as required .
Anti-fire: anti-fire device installed between cabin and generator as optional as required .
Anti-fire door closes when too much smoke or flame occurs,avoiding flame into cabin
Water paint device :Water paint device as optional .Two rows or three rows of nozzles installed on each side of top 45°,
Or 2 extra nozzles device at the rear corners Traditional booths can be changed into water paint boos
in this way.
Enviromental protection system : 4 types environmental-protection systems as optional .
Water curtain as optional as required.
Spray booth using life time
| Filtration system | Working time | |
| Ceiling filter | 400-450 working hour | |
| Primary ceiling filter | 60-80 working hour | |
| Floor fiber glass filter | 200 working hour | |
| Exhausted box filter and active carbon | 80-100 working hour | For option |
Packing Standard :
Each part all has label number which is easy for installation .
Model of transportation is mainly with container transportation .
The product is modular needs one set 1.5T forklift to be loading & unloading tool .
It only needs 2 operations to finish the unloading .
Leeds International Development Co., Ltd is a manufacturer and supplier with all kinds of spray booth, industrial spray booth, auto car lift, lifting table, body collision straightening bench, scanner, wheel alignment, tire changer, wheel balancer, spot welding machine and other auto maintenance equipments and tools since 2008.
Most of our products, meet the CE standard, cost-effective and worthy of your choice, have been shipped to worldwide markets more than 80 countries (Europe, North & South America, Africa, Australia, the Middle East and Asia as well as different provinces in China).
Quality First, Service Highest is the policy carried by all members. With good credit and excellent service, we have established long-term cooperative relationship with many companies. For customers, we service the future based on good faith.
For business partner, we work seriously, dependable, and cherish every cooperating with each other. For employees, we are bearing in mind the principle of people-oriented, the pursuit of excellence, mutual respect and unity of purpose with new high.
We are guided by the philosophy of innovation, sincere cooperation and manual development. We hope to create a brilliant and win-win cooperation with you. Welcome all of you come for visiting, investigating and negotiating.
