Steyr Tractor Wd615 Engine Cylinder Liner OE 61500010344

Steyr Tractor WD615 Engine Cylinder Liner 61500010344

Specifications

Part Name	Cylinder Liner
P/N	61500010344
Application	steyr WD615
Condition	New and Standard
Packing	Carton or as customer's requirement

Product Name: Cylinder Liner
Apply For: Steyr
Engine Model: WD615
OEM No.:  61500010344
 
 Remarks for cylinder liner: 

Liner we make	Wet liner, Dry liner, Air cooled liner
Liner we offer	full finished (FF) and semi finished (SF) cylinder liners
Liner material	Steel, Cast iron
Liner application	Diesel engine, Gasoline engine
Suitable scope	Truck, Car, Tractor, Excavator, Marine etc.
Protection	100000 miles guaranteed, 12 month warranty
Packing	Strong package, Pack as you want.
Delivery	By ship or air

1)Wet cylinder
 
The location bores and particularly the running surfaces in the cylinder block must be cleaned carefully and they must be undamaged. Corroded surfaces must be reworked (used flange liners and outer diameter oversize liners). As this is done, make sure that the liners moves in easily and that they take up the correct position (the projecting length of the liner must be in accordance with the regulations of the engine manufacture). After the liner has been installed with the seat rings that belong to it.
 
(use slip agent), the cylinder diameter is to be checked particularly in the region of seal rings so as to determine whether any deformation has been caused by pinched sealing rings. Using the wrong sealing rings (wrong diameter/ wrong materials) can a narrowing of the cylinder which can lead to engine damage.The cooling system should be pressure tested after the liners have been installed so as to determine whether there is any leakage before the engine is started.
 
2)Semi-finished cylinder liner
 
The surface which supports the flange must be vertical to the location bore and it must be sufficiently and evenly beveled. If the liner flange is unevenly supported it can tear off. After the installation of the liner, which is only semi-finished in its inside diameter, this cylinder boring is finely bored and then finished by honing until it has the specified dimensions or, in the case of finely bored liner.It is only finished by honing (tolerance accordingly to DIN ISO H5). The surface of the liner must be flush to the sealing surface of the cylinder block, if necessary,the block surface and the liner must be finished by surface grinding.
 
3)Finished Cylinder liner
 
Before the liner is installed, the location bore in the cylinder block must be cleaned carefully and must be checked to ensure the accuracy of the dimensions and to determine whether any distortion has occurred. Out of center or damaged bores can be reworked for the installation of oversize liners. It is important for this that the locating bore is cylindrical, as this is what determines the geometrical shape of the inside of the pressed in, thin walled liner.
 
 
4)Air cooling cylinder liner
 
In accordance with the instructions from the engine manufacture, cast iron cylinders or light alloy cylinders are used. 
 
Light alloy cylinders are separated into several groups due to the small installation clearance in the standard cylinder dimensions
 
 Our Liner Stocks for following multi-function engine parts:

Yanmar:	3TNE84, 3TNE88, 4TNE88, 4TNA94, 4TNA98, 4TNV98
Kubota:	D1462-DI, F2302-DI, F2803-B, V3300-B, V3300-B. V3300-DIE, V3300-TIE
Shibaura:	N844, N844L, N844T
Isuzu:	3AE1, 3KB1, 3KC1, 3KC2, 3KR1, 3KR2, 3/4LB1, 3/4LC1, 3LD1, 4FB1, 4FC1, 4FD1, 4FE1, 4FG1, 4FG1T, 4JB1, 4JG2, 4LE1, 4LE2, D201
Komatsu:	4D94, 4D94E, 4D95A, 4D95K, 4D95LE-3, 4D95LE, 4D95S, 4D95T, 4D98E, S4/6D95T, 4D105-3, 4D120, 4D130, 6D105-1, 6D105, 6D155, S6D95, S6D102, S6D105-3, S4/6D105-5, S6D108, S6D108, S6D110-2, S6D110-3, S6D110, S6D125, S6D140, S6D170, NH220, NH250
Mazda:	WL B2500, S2 E2200, XA E2500, XB E2700, HA E3000, XA T2500, HA T3000, VS T3000, T3500, SL T3500, TF T4000, ZB T4100, TM T4500
Mitsubishi:	4DQ5, K3B, K3F, K3H, K3M, K4C, K4D, K4E, K4E-DI, K4F, K4H, K4M, K4N, K4Q, 4DQ7, L3C, S3E, S3L2, S4E, S4E2, S4F, S4L, S4L2, S4L2-T, S4Q2, S4Q2-1, S4S, S6E2, S6KT, S6SD
Nissan:	BD30, H20, K21, K25, SD22, SD23, SD25, TD23, TD25, TD25T, TD27, TD27T
Toyota:	1DZ-2, 1DZ, 1Z, 2H, 2J, 2Z, 2Z-N, 12Z, 13Z, 14Z

Name of Material

C

S

Si

P

Mn

Cr

B

Cu

Ni

V+Ti

Mo

Mechanical Properties

Boron Cast Iron

2.8~3.6

<=0.12

2.0~2.7

<=0.5

0.7~1.2

0.3~0.5

0.04~0.08

Brinell Hardness>210HB, σb>=200Mpa

Boron Copper Gray Cast Iron

2.8~3.6

<0.2

2.0~2.7

<=0.5

0.7~1.2

0.2~0.5

0.04~0.08

Right amount

Brinell Hardness>210HB, σb>=240Mpa

Vanadium, Titanium Gray Cast Iron

3.0~3.6

<0.2

2.0~2.7

<=0.5

0.6~1.2

0.2~0.5

>=0.3

Brinell Hardness>210HB, σb>200Mpa

Molybdenum Nickel Copper Gray Cast Iron

2.8~3.6

<0.2

1.8~2.4

<=0.3

0.5~1.0

0.2~0.5

0.3~0.6

Right amount

Right amount

Brinell Hardness>210HB, σb>235Mpa

Bainite Gray Cast Iron

2.7~3.3

<0.10

1.7~2.5

<=0.3

0.3~0.7

0.~0.5

Right amount

Right amount

Right amount

Brinell Hardness270~330HB, σb>350Mpa

Nickel Copper Gray Cast Iron

2.8~3.7

<0.12

1.8~2.7

<=0.3

0.5~1.2

0.15~0.5

Right amount

Right amount

Brinell Hardness>200HB, σb>196Mpa

Specification:
 
Application for:  All Car Models
 
production capacity:500,000 pieces/month
 
Warranty:  1-2 years or 60,000-80,000 kms
 
Delivery time: 7--60 days atfer received deposit
 
Service:
 
1. New products can be developed upon customers' sample or drawing.
 
2. Factory supplier owning attractive price.
 
3. Samples can be sent for customers to check the quality before ordering
 
4. Accepting trail order.
 
5. Free simple laser mark can be offered .
 
Contact information:


ANQING XINYI AUTOPARTS CO.,LTD.
NO.80 Tianzhushan Road, Anqing City,  Anhui Province,PRC
 
TEL: +86-556-5675229 /5171002          Sophie
FAX: +86-556-5171000