The manual worm and roller steering gear is used by various manufacturers. This steering
Gear has a three-turn worm gear at the lower end of the steering shaft. Instead of a sector or tapered peg on the pitman arm shaft, the gearbox has a roller
Assembly (usually with two roller teeth) that engages the worm gear. The assembly
Is mounted on anti-frictional bearings. When the roller teeth follow theworm, the rotary motion is transmitted to the pitman arm shaft, pitman arm and into
The steering linkage
The Pitman arm is a linkage attached to the steering gear (see recirculating ball) sector shaft, that converts the angular motion of the sector shaft into the linear motion needed to steer the wheels. The Pitman arm is supported by the sector shaft and supports the drag link or center link with a ball joint. It transmits the motion it receives from the steering box into the drag (or center) link, causing it to move left or right to turn the wheels in the appropriate direction. The idler arm is attached between the opposite side of the center link from the Pitman arm and the vehicle's frame to hold the center or drag link at the proper height. A bad pitman arm can cause play in the steering, and may get worse over time.
A Pitman shaft is a column extending from the steering sector, which attaches to the Pitman arm, which moves the tie rods. Depending on the turn direction, the fluid from a pump moves a piston forward or backward. This action moves a nut, which turns the Pitman shaft and steering linkage. The movement inside the steering box causes the Pitman shaft and arm to rotate, applying leverage to the relay rod, which passes the movement to the tie rods.
Features:
Steering Shafts
Disconnect the steering shaft from the steering box input shaft. Often the upper end of the steering shaft will have a splined section, which will allow the shaft to be collapsed slightly and enable you to clear the steering box input shaft. Next, look for the large bolts attaching the steering box to the frame. Remove this hardware, being careful to support the surprising weight of the steering box as the last bolt is removed. Lower the unit down and out of the underside of the vehicle. If this is not possible due to space constraints, the box will have to come up through the engine compartment, which may require temporary removal of accessories like the alternator or power steering pump. On vehicles equipped as such, check the ball joint on the end of the pitman arm for excessive play, and if you have not already done so swap the pitman arm to the new steering box. Install the new steering box in the vehicle, reattach the steering shaft, hoses, and steering linkages, being sure to torque all hardware to the manufacturer's specifications. Refill the power steering pump reservoir with the proper fluid, reconnect the battery, and start the engine. Look for any fluid leakage, then begin turning the steering wheel back and forth from lock to lock. Shut off the engine after each pass, checking and refilling the power steering pump reservoir to the proper level. Air will slowly escape the system, so check the fluid level every few days after the installation. Assuming the ball joints and the rest of your steering components are in satisfactory condition, you should now be enjoying "like new" steering, and vehicle wandering will be a thing of the past!
Also welcome to work with us together for the following steering pitman shaft for OEM or aftersale market
ACURA / ACURA TRUCKS / AUDIBMW / BUICK / CADILLAC
CHEVROLET / CHEVROLET/GMC TRUCKS / CHRYSLERCHRYSLER TRUCK / DODGE / DODGE TRUCK
EAGLE / FORD & MERCURY / FORD TRUCKGEO / HONDA / HONDA TRUCKS
HYUNDAI / HYUNDAI TRUCK / INFINITIINFINITI TRUCKS / ISUZU / ISUZU TRUCKS
JAGUAR / JEEP / KIAKIA TRUCK / LEXUS / LEXUS TRUCKS
LINCOLN / MAZDA / MAZDA TRUCKMERCEDES / MERCURY / MERCURY TRUCK
MERKUR / MITSUBISHI / MITSUBISHI TRUCKNISSAN / NISSAN TRUCKS / OLDSMOBILE
OLDSMOBILE TRUCK / PLYMOUTH / PLYMOUTH TRUCKPONTIAC / PONTIAC TRUCK / RENAULT
SAAB / SATURN / SCIONSUBARU / SUZUKI / TOYOTA
TOYOTA TRUCK / VOLKSWAGEN / VOLVO
PART NUMBER LISTING - REMANUFACTURED STEERING PUMPS (IMPORT & DOMESTIC)
Other relative steering gear parts for a reference:
Our workroom&company at glance:
We attend some professional fair Chin and abraod,at a glance:
INGBO CIE INDUSTRY AND TRADE Co., Ltd was established from 1988 in China and export more than 30 years old mainly for Industrial bearing Our Head Company registered capital is USD1, 500, 000, and we have 1, 200 employees contributing to the turnover of more than 0.8 billion US dollars.
We have passed the evaluations of ISO9001: 2001 quality management system, ISO14001: 2004 environment management system and OHSAS18001: 1999 certification. We possess more than ten subsidiary companies, an industrial zone named CIE Industry occupying 25, 000 square meters, and more than ten manufacturing factories respectively engaged in high quality automotive parts and bearings, including automotive wheel bearings and kits, auto bearings, automotive bearings, wheel-hub units and kits, air-conditioner compressor bearings, steering-gear bearings, deep groove ball bearings, tapered roller bearings, needle roller bearings and special non-standard bearings, ball screw, linear guide rail and block assembly, steering systems with power steering gear, manual steering gears like recirculating balls and nut steering gears, racks and pinion steering gears, steering columns, steering linkages, as well as steering gearbox parts like gear sector shafts, worm assemblies and ball screws, linear guide rails and block systems. You can find our products installed as OEM equipment in automobiles from Europe, Asia and the U. S. A.
Our subsidiary company-CIE Auto Source Industry Co., Ltd. Was established in 1996, and is strong at the production of bearings, Power Transmission Parts and Steering System, of which the details focus on the following issues:
Design strength:
Our in-house team of approximately 60 experienced engineers is constantly developing newer and better bearing models, and auto parts mainly for steering systems. The most advanced computer aided design (CAD) systems and Germany-imported grinder machines are utilized to incorporate your specific requirements. Our ratio of R&D investment is much higher than the average in domestic industry.
Quality control:
Some of our QC instruments and meters are imported from Japan and Germany. We inspect every item with Talyrond roundness testing instruments before packaging. Our team also performs noise and vibration tests as well as radial and axial clearance inspection. Steering system parts are inspected on fatigue test bench, metering inspection center, 3D measuring apparatus, performance test bench and alignment test bench.
Services:
We are committed to providing first class services and top quality products through:
1)Developing trading relationships of mutual trust with customers and suppliers;
2)Training and development of all our employees to enable them to release their full potentials and provide career progression;
3)Supporting objectives which safeguard the environment, leading to better working practices and safety running of machine and operation;
4)Improving efficiency by incorporating technological solutions
5)Exceeding customer's expectation for service, quality and value for money\
6)Improving communications with our customers, suppliers and staff to keep them up to date with industrial development and news
Constantly contacting customers for product's further development is given higher priority at NINGBO CIE INDUSTRY AND TRADE Co., Ltd., and serious development work relies on knowing the demands and requirements of the market.
