Industrial painting Spray Oven with diesel burner BD730-7000
Booth Body:EPS or Rock wool panel Wall panel :sandwich style,thickness 50mm,polystyrene or cock wool available as required .
Panels are tongue and groove connected .Roof panel is galvanized metal sheets,hot-isolated panel as optional .
Door:new style is without aluminum side,reinforcement inside,while old style is with aluminum side.
Personnel door with pressure lock automatically opens when inside pressure exceeds.
There is auto-return device on top of personnel door of some models .
Basement is made of steel ,galvanized ,easy assembled .
2rows of grids and 3rows of vein boards, or full grids,good bearing ,antisepsis and reliable .
Ramp :2pcs or full vein boards.
Intake and exhaust Cabin Centrifugal fan,big vane and motor separated ,avoiding accidents resulting from short circuit .Centrifugal fan produces great air flow ,is easy to clean dust on vane,and is up to CE standard. In take fan is a must for all models ,while exhaust fan is collocated for some models.
European flange style ducts.Exhaust ducts are must for all models while intake ducts are collocated for some models.Manual or electrical damper to adjust air flow .
Spraying-baking transform damper ,air controlled .
Intake and exhaust ducts are separated ,avoiding interaction
Cleaning system
Twice filtration:the first one is at inlet,filtering dust above 15um,the second one is at the bottom of roof air chamber .multi-layers, good seal ,filtering dust above 5um ,up to 98% filtration rate. Four sides of filters are hided in the support trough ,assuring good seal .
Heating : Diesel burner ,fired after flame,reliable and completely burnt.
Heating exchanger ,made of stainless steel, large exchange area ,and high efficiency.
Oil tank ,oil display tube,and oil filter collocated .
Lighting :Top lights:45° assembled,tubes are different according to different models.
Sides lights:differ according to different models,700-1000Lux lighting.
Control board : Control box :high quality components ,overload ,overheat ,phase-lacking protection.Heat sensor at
inlet works when heat exceeds .The whole operation can be done after spraying/baking is preset once.
SCM as optional as required .
Anti-fire: anti-fire device installed between cabin and generator as optional as required .
Anti-fire door closes when too much smoke or flame occurs,avoiding flame into cabin
Water paint device :Water paint device as optional .Two rows or three rows of nozzles installed on each side of top 45°,
Or 2 extra nozzles device at the rear corners Traditional booths can be changed into water paint boos
in this way.
Enviromental protection system : 4 types environmental-protection systems as optional .
Water curtain as optional as required.
| BD-730 Non-standard (6.9×3.9×2.65m) (Gas Burner ) |
| Booth Dimensions | | |
| -Internal Size(L×B×H) | 6900×3900×2650mm (L×W×H) | |
| -External Size(L×B×H) | 7000×5460×3400mm(L×W×H) | |
| Foundation and Floor | | |
| Basement Description | 300mm,two rows of grids with three rows of pattern plate ,galvanized plate welding ,2pcs ramp :620*2000(W×L) | |
| Load Capacity | 650kg/single wheel | |
| Filter Area | 10m2 | |
| Wall Panel | | |
| Wall Panel | 50mm EPS sandwich panel ,steel sheet thickness:0.426mm | |
| Roof | Single-layer galvanized plate | |
| Door | | |
| Entrance Door | Hand made door ,2+1 structure | |
| Door Size | 3000×2600 mm (W×H) | |
| Door arrangement and QTY | 1 set entrance door | |
| Door description | With frame inside,fill with high temperature resistant EPS | |
| Service Door | | |
| Description | Frame Structure , 1 set ,size :800×1850 mm (W×H) | |
| Side lights | Optional | |
| Top Lights | | |
| Description | 8units, each unit 3×16W, LED TUBES,on top 2 sides | |
| Illumination | > 750Lux | |
| Filtration system | | |
| Pre filter | G2Grade plate type filter | |
| Ceiling filter | F5 grade filter ,model SP-600G | |
| Bottom paint-mist collection and exhaust filter | Fiber glass paint-stop filter ,with features of big air ventilation volume ,small resistance ,fire resistance and so on | |
| Inlet System | | |
| Description | 1*7.5KW,970 rpm, 380 V, 50 Hz,25000m3/h 620pa turbo fan | |
| Exhaust System | | |
| Description | 1*7.5KW,970 rpm, 380 V, 50 Hz,25000m3/h 620pa turbo fan | |
| Heating System | | |
| Heat exchanger | Stainless steel 1Gr18Ni9Ti(SUS304),158KW | |
| Heating Time | 8-10minutes (from 20° to 60°ºС) backing status | |
| Burner Type | FS20 Gas Burner ,2000000kcal/h | |
| Ducting | | |
| Qty | 3pcs Straight Duct , 1x 90°,1x45°,1 deduct | |
| Control Box | | |
| Standard | BS EN 60204:2006+A1:2009 | |
| Fuction | Painting,warming painting,baking,lighting,emergency stop,temperature,failure indication. | |
| Control Box | | |
Leeds International Development Co., Ltd is a manufacturer and supplier with all kinds of spray booth, industrial spray booth, auto car lift, lifting table, body collision straightening bench, scanner, wheel alignment, tire changer, wheel balancer, spot welding machine and other auto maintenance equipments and tools since 2008.
Most of our products, meet the CE standard, cost-effective and worthy of your choice, have been shipped to worldwide markets more than 80 countries (Europe, North & South America, Africa, Australia, the Middle East and Asia as well as different provinces in China).
Quality First, Service Highest is the policy carried by all members. With good credit and excellent service, we have established long-term cooperative relationship with many companies. For customers, we service the future based on good faith.
For business partner, we work seriously, dependable, and cherish every cooperating with each other. For employees, we are bearing in mind the principle of people-oriented, the pursuit of excellence, mutual respect and unity of purpose with new high.
We are guided by the philosophy of innovation, sincere cooperation and manual development. We hope to create a brilliant and win-win cooperation with you. Welcome all of you come for visiting, investigating and negotiating.
