6170 Weichai Engine Parts Cylinder Liner 610800010325 Marine
Specifications
Part Name | Cylinder Liner |
P/N | 610800010325 |
Application | Weichai 6170 |
Condition | New and Standard |
Packing | Carton or as customer's requirement |
Product Name: Cylinder Liner
Apply For: WEICHAI
Engine Model: 6170
OEM No.: 610800010325
1- 8 production lines and strong casting ability for cylinder liners;
2- Wet and dry cylinder liners;
3- Slip Fit (F), Press Fit (SF);
4- Their diameters can range from 55 to 250mm;
5- Oxidation phosphor reason and the plasma, laser hardening;
6- DIN/ISO4383 and ISO/TS16949 certificated;
1)Wet cylinder
The location bores and particularly the running surfaces in the cylinder block must be cleaned carefully and they must be undamaged. Corroded surfaces must be reworked (used flange liners and outer diameter oversize liners). As this is done, make sure that the liners moves in easily and that they take up the correct position (the projecting length of the liner must be in accordance with the regulations of the engine manufacture). After the liner has been installed with the seat rings that belong to it.
(use slip agent), the cylinder diameter is to be checked particularly in the region of seal rings so as to determine whether any deformation has been caused by pinched sealing rings. Using the wrong sealing rings (wrong diameter/ wrong materials) can a narrowing of the cylinder which can lead to engine damage.The cooling system should be pressure tested after the liners have been installed so as to determine whether there is any leakage before the engine is started.
2)Semi-finished cylinder liner
The surface which supports the flange must be vertical to the location bore and it must be sufficiently and evenly beveled. If the liner flange is unevenly supported it can tear off. After the installation of the liner, which is only semi-finished in its inside diameter, this cylinder boring is finely bored and then finished by honing until it has the specified dimensions or, in the case of finely bored liner.It is only finished by honing (tolerance accordingly to DIN ISO H5). The surface of the liner must be flush to the sealing surface of the cylinder block, if necessary,the block surface and the liner must be finished by surface grinding.
3)Finished Cylinder liner
Before the liner is installed, the location bore in the cylinder block must be cleaned carefully and must be checked to ensure the accuracy of the dimensions and to determine whether any distortion has occurred. Out of center or damaged bores can be reworked for the installation of oversize liners. It is important for this that the locating bore is cylindrical, as this is what determines the geometrical shape of the inside of the pressed in, thin walled liner.
4)Air cooling cylinder liner
In accordance with the instructions from the engine manufacture, cast iron cylinders or light alloy cylinders are used.
Light alloy cylinders are separated into several groups due to the small installation clearance in the standard cylinder dimensions
Our Liner Stocks for following multi-function engine parts:
Yanmar: | 3TNE84, 3TNE88, 4TNE88, 4TNA94, 4TNA98, 4TNV98 |
Kubota: | D1462-DI, F2302-DI, F2803-B, V3300-B, V3300-B. V3300-DIE, V3300-TIE |
Shibaura: | N844, N844L, N844T |
Isuzu: | 3AE1, 3KB1, 3KC1, 3KC2, 3KR1, 3KR2, 3/4LB1, 3/4LC1, 3LD1, 4FB1, 4FC1, 4FD1, 4FE1, 4FG1, 4FG1T, 4JB1, 4JG2, 4LE1, 4LE2, D201 |
Komatsu: | 4D94, 4D94E, 4D95A, 4D95K, 4D95LE-3, 4D95LE, 4D95S, 4D95T, 4D98E, S4/6D95T, 4D105-3, 4D120, 4D130, 6D105-1, 6D105, 6D155, S6D95, S6D102, S6D105-3, S4/6D105-5, S6D108, S6D108, S6D110-2, S6D110-3, S6D110, S6D125, S6D140, S6D170, NH220, NH250 |
Mazda: | WL B2500, S2 E2200, XA E2500, XB E2700, HA E3000, XA T2500, HA T3000, VS T3000, T3500, SL T3500, TF T4000, ZB T4100, TM T4500 |
Mitsubishi: | 4DQ5, K3B, K3F, K3H, K3M, K4C, K4D, K4E, K4E-DI, K4F, K4H, K4M, K4N, K4Q, 4DQ7, L3C, S3E, S3L2, S4E, S4E2, S4F, S4L, S4L2, S4L2-T, S4Q2, S4Q2-1, S4S, S6E2, S6KT, S6SD |
Nissan: | BD30, H20, K21, K25, SD22, SD23, SD25, TD23, TD25, TD25T, TD27, TD27T |
Toyota: | 1DZ-2, 1DZ, 1Z, 2H, 2J, 2Z, 2Z-N, 12Z, 13Z, 14Z |
Name of Material | C | S | Si | P | Mn | Cr | B | Cu | Ni | V+Ti | Mo | Mechanical Properties |
Boron Cast Iron | 2.8~3.6 | <=0.12 | 2.0~2.7 | <=0.5 | 0.7~1.2 | 0.3~0.5 | 0.04~0.08 |
|
|
|
| Brinell Hardness>210HB, σb>=200Mpa |
Boron Copper Gray Cast Iron | 2.8~3.6 | <0.2 | 2.0~2.7 | <=0.5 | 0.7~1.2 | 0.2~0.5 | 0.04~0.08 | Right amount |
|
|
| Brinell Hardness>210HB, σb>=240Mpa |
Vanadium, Titanium Gray Cast Iron | 3.0~3.6 | <0.2 | 2.0~2.7 | <=0.5 | 0.6~1.2 | 0.2~0.5 |
|
|
| >=0.3 |
| Brinell Hardness>210HB, σb>200Mpa |
Molybdenum Nickel Copper Gray Cast Iron | 2.8~3.6 | <0.2 | 1.8~2.4 | <=0.3 | 0.5~1.0 | 0.2~0.5 |
| 0.3~0.6 | Right amount |
| Right amount | Brinell Hardness>210HB, σb>235Mpa |
Bainite Gray Cast Iron | 2.7~3.3 | <0.10 | 1.7~2.5 | <=0.3 | 0.3~0.7 | 0.~0.5 |
| Right amount | Right amount |
| Right amount | Brinell Hardness270~330HB, σb>350Mpa |
Nickel Copper Gray Cast Iron | 2.8~3.7 | <0.12 | 1.8~2.7 | <=0.3 | 0.5~1.2 | 0.15~0.5 |
| Right amount | Right amount |
|
| Brinell Hardness>200HB, σb>196Mpa |
Specification:
Application for: All Car Models
production capacity:500,000 pieces/month
Warranty: 1-2 years or 60,000-80,000 kms
Delivery time: 7--60 days atfer received deposit
Service:
1. New products can be developed upon customers' sample or drawing.
2. Factory supplier owning attractive price.
3. Samples can be sent for customers to check the quality before ordering
4. Accepting trail order.
5. Free simple laser mark can be offered .
Contact information:
ANQING XINYI AUTOPARTS CO.,LTD.
NO.80 Tianzhushan Road, Anqing City, Anhui Province,PRC
TEL: +86-556-5675009/ 5171002
FAX: +86-556-5171000
Anqing Xinyi Auto Parts Co., Ltd. is located in the Industrial Zone of Anqing Economic and Technological Development Zone. We are a professional factory to produce engine valve, valve seat and valve guide, and we have independent import and export rights.
We also can supply cylinder head, cylinder liners, crankshaft, camshaft and other related products.
As a professional factory, we have been specializing in the export of auto parts more than 10 years. Our products sell well in many countries and regions, such as South America, Europe, the Middle East, Southeast Asia and Afica.
For serving clients better, we have registered some brands as our own, and we have the brand proprietorship of OSVAT, PAGZD, XYTOSAN, KOSFA and GPM in China.
Based on our proficiency in technical skills and rich experience, we will provide high-quality products and good services for you. Our spirit is "dedication, innovation, teamwork, and hard-working".
Both new and old customers are welcome to visit our company.